Getting Android car stereo installed professionally will cost you a lot of money, and you’ve likely already spent quite a bit on purchasing the equipment.That’s why installing it yourself might be a good way to go. It’s entirely possible to do it all yourself, as long as you have the proper tools, wiring diagrams, and instructions. Depending on what you’ve purchased, it may also entail a significant time investment.
One very important point to remember: Always disconnect the negative connection on the car’s battery before you do any type of work to avoid shocking yourself or damaging your new equipment.
Installing coaxial speakers is fairly simple. These involve removing the front or rear factory speakers and simply swapping in the new ones while making sure the wiring is correct. Component speakers are a bigger job. Since you’re going to be putting multiple new parts in your car, like tweeters and woofers, this could involve some cutting or drilling into the doors or A-pillars. In some cases, you’ll need to be able to take apart your car door to accomplish this. The job may also involve some soldering. In addition, adding subwoofers to your car almost certainly means cutting holes in the trunk or rear compartment.
If you’re adding a new stereo receiver, that means you’ll need to remove the old one — usually by removing the bolts or even using special tools — then properly connecting the wires to the new head unit. Again, there may be wire cutting and soldering involved here, too. Your dashboard might also need to be modified to accommodate the new stereo if it’s a different size.
As a general rule, amps should be installed at least 3 feet (0.9 meters) from the receiver to prevent interference. The most popular method involves installing them under the seat or in the trunk. You’ll need to wire the amplifier into the car’s electrical system to power it, which can be complicated.
So what could go wrong if you install things incorrectly? A lot of things, actually. The speakers could be out of phase and sound distorted, you could cut the mounting point incorrectly and leave a gaping hole in your car door or you could wire it wrong and short out your electrical system. You run the risk of permanently damaging your car and your new stereo equipment if you do this wrong. In other words, unless you have the right tools, the right instructions, and the right experience, it may be worth the extra cost to have a professional install it.
Related Posts
How to Install an Android Car StereoFirst, turn off the electricity to the machine by removing the live battery wire from its station. After disconnecting the battery, you’ll need to take off the trim boards enveloping your car stereo. Each car just a tiny bit unique here. Next, you need to dispatch the previous head unit directly out until the wires connected to the back are accessible. Unplug the cord, discharge the cabling harness and proceed to remove the antenna cable by unscrewing it. The cabling harness is the structural fastener that integrates all of the cabling for the sound system into an individual connection. The new head unit you have purchased should have included an adapter that matched the factory installed cabling. The end of the cabling on the end, should have four to eight colored wires coming from the back. There should be two such wires that plug to each speaker; one positive one negative. Most negatives are shown with a black stripe while positives are generally either solids or have a white stripe. If your new car DVD player does not come with an adapter that works with the harness in the dash, you need to purchase a cabling harness kit. The new harness will have to be plugged into the new stereo. Match the colored wire to its match and put them together. After having the wires connected to their proper match, the stereo should be ready to install. Hold the system to the dash to plug the proper connections into the back. You can pause and test what you have done to make sure you have correctly pared the wires. Once you find that everything is in order; proceed to carefully push the unit all the way into the dash and replace the screws. After the stereo is mounted correctly, put the trim boards back up and reattach everything holding them in place. Finally, you got a new Android stereo for your car.
FAQ for Android Car Stereo Amplifier1.How can I populate my address book’s contacts into the Android car stereo universal? A: For downloading the address book’s contacts from your phone to the radio: firstly, you need to pair your phone with the Android head unit, then please click the contacts icon and search your contacts like the following picture: Please make sure that you use the built-in contacts in your phone, otherwise it can not be searched. Also, if your smartphone runs Android 5.0 OS or above, please allow all the submissions in your phone when the stereo searches the contacts. 2.After installing the car DVD player, I can’t hear any sound through the speakers or the Bluetooth. The music is attenuated but no phone or GPS instructions can be heard. Is there a hidden menu to give more volume to GPS and Bluetooth? A: Normally, we don’t have hidden menu to give more volume. And for setting the GPS app sound ( we pre-installed the IGO free copy version ), please check the setting below: You can re-install the IGO app from our SD card to check whether it would help or not. Besides, please enter the settings=>GPS, make sure that you turn on the GPS monitoring. You can turn up the GPS mixing ratio so that the GPS sound would be louder. As for the Bluetooth issue, if you make the phone call via Bluetooth, please well close your car windows and doors, then turn the volume of both your phone and the head unit to the middle level. You can also enter the factory setting ( the password is 126 ), and check the BT setting. 3.In case of the extra mic, how can I increase the volume ? I don’t find any possibility to adjust the mic volume in the car audio player. A: Please use the extra mic and increase the car radio’s volume. 4.I’m not able to get torque to recognize that Bluetooth is on. Therefore, I can’t connect Bluetooth to the OBD. I can connect to it from my phone but not from the Pumpkin Car Head Unit. Is there something I can do to get this to work ? A: For pairing the OBDII, you need to know the protocol of your car and select the correct protocol in “Torque”. Followings are the whole instruction: ①Please enter “Bluetooth ”application, then set the pairing code of the radio to the same one as the OBDII scanner’Generally, it would be 0000 or 1234. ( please try both ) ②Then please open the built-in torque, choose the OBDII scanner MAC address in the application setting and choose your car protocol. 5.How do I change the default music app ? A: Since the car DVD player Bluetooth is based on Android 4.4, you can download other music player apps like Spotify in the built-in play store ( need Wifi or other Internet source ) and install it on the head unit.…
FAQ for Pumpkin KD-C0223 Android 4.4 Car StereoQ1. Does it fit in a Nissan Xtrail 2011 ? A:Sorry, it doesn’t. There is another Pumpkin Car Stereo which fits Nissan Xtrail 2011:http://www.autopumpkin.com/pure-android-4-2-twin-din-universal-nissan-car-dvd-gps-navigation-with-6-2-inch-lcd-hd-capacitive-touch-screen-3g-wifi-bluetooth-support-obd2.html Q2.Does the Android operating system allow calls and txts from Google Hangouts and Google voice ? A:Sorry, the builtin mic of the Car DVD Player is specifically designed for the Bluetooth phone call. Q3.It says OBD2, but how does that work? Does it read engine error codes ? A:Here is an instruction video about it : https://www.youtube.com/watch?v=XZ9Cw-xvkx8&feature=youtu.be&list=UU5idhlXZfjcSV9KDp-gcCOw Q4.Can you make /receive calls while using the navigation ? A:Yes. A banner comes on at the bottom of the screen no matter what app you’re in. It has a few buttons, one is for answer, another is for ignore. Q5.Can this be tethered to a cellphone via Bluetooth for internet access ? A:Sorry, it can’t. But you can share your cellphone as Wifi hotspots, then use the radio to connect to the wifi signal from your cellphone and use the internet. Q6.What is the unlock code to get to the advanced options ? A:You can find it in the manual, which is 126. Q7.Can you control high and low pass filters with this unit? A:There is an equalizer in the music program. You can get apps that might better fit your needs as this head unit is running Android system.…